Construct and redraw series and parallel circuit paths
Translate descriptions into clear low-voltage schematics and recognize the same connections in differently shaped drawings.
Exam scope and assessment notes
Mapped to the named 0973 section using teaching from the corresponding single-science course. A 0973-specific review of every Core and Supplement objective is still in progress. Written practice is self-checked; it does not demonstrate supervised laboratory competence or award an official Cambridge grade. This qualification reports two grades on the 9–1 scale; confirm the entry route for your zone and exam series.
Before you begin
- Draw source and load symbols.
- Interpret junction dots and switch contacts.
Work on paper. Try each question before revealing help, and explain why your method works.
Quick readiness check
What does a junction dot show?
What you will learn
- Draw series and parallel arrangements.
- Recognize branch endpoints and a complete source return.
Define the connection pattern
Two components in series lie in one path so the path passes through one and then the other without splitting between them. Components in parallel are connected between the same pair of junctions, each with its own branch path. Side-by-side placement alone does not make components parallel.
To draw two parallel loads, identify junctions A and B, connect a complete load path from A to B for each, and connect the source across A and B. Draw dots at the splits and joins. Trace the source–branch–return loop for each load separately.
Plan construction from the diagram
For teacher-supervised isolated low-voltage construction, begin with the supply off and a checked diagram. Match wires to terminal connections, use suitable ratings and meters, inspect for unintended bypasses, then ask the teacher to check before energising. A diagram exercise does not demonstrate competent construction or practical assessment.
Redrawing a rectangular loop into a different shape preserves the circuit if the same terminals remain connected. A branch wire directly joining A and B without an intended load is a short across that pair, not a useful extra parallel resistor. Keep topology and operating limits clear.
Sources for this lesson
Pause and explain
Two loads are side by side but connected one after another in one loop. What is their arrangement?
Worked example
Describe a diagram with two resistors each connected from junction A to junction B and a source across A and B.
Show the worked solution
- Both resistors share the same endpoint pair.
- Each provides a separate branch path.
- The resistors are connected in parallel.
Answer Two resistors in parallel across the source.
Try a topic test
Choose Easy, Normal or Difficult. Save your answers and open worked review after finishing.
Test this topic →From guided practice to a new situation
Write your answer and reasoning first. Use a hint only if you are stuck. The model solution is for self-checking; your written work is not automatically marked.
Draw two lamp symbols in series with a cell and closed switch.
Give me a hint
Make one path pass through both lamps before returning.
Compare my reasoning
- Draw the cell and closed switch.
- Place both lamp symbols successively in the same path.
- Complete the return wire without a split between lamps.
One complete unbranched loop through both lamps.
Look for these in your work
- Draw recognizable symbols.
- Avoid an unintended bypass.
Redraw the two lamps in parallel with a common source switch.
Give me a hint
Define and dot the two common branch junctions.
Compare my reasoning
- Draw two junctions A and B.
- Connect each lamp in its own A-to-B branch.
- Connect the cell and common switch across the arrangement.
Two complete lamp branches between the same junction pair, with a shared source switch.
Look for these in your work
- Show both endpoint connections.
- Locate the common switch correctly.
A proposed third parallel branch is only a plain wire across the ideal source. Explain the error and a suitable paper correction.
Give me a hint
A branch needs an intended load rather than a direct source bypass.
Compare my reasoning
- The wire connects the source endpoints with negligible resistance.
- It bypasses the loads and represents a short.
- Remove that bypass in the diagram or replace it with the intended rated load before any teacher check.
The plain-wire branch shorts the source; remove the unintended bypass from the diagram.
Look for these in your work
- Identify the actual endpoint pair.
- Keep this as a supervised diagram exercise.
Common mistakes
- Physical proximity does not determine topology.
- Both endpoint connections must match for parallel.
- A plain-wire source bypass is a short.
What can you explain now?
What defines two parallel components?
Compare with the explanation
They connect across the same two junctions.
The shared endpoint pair defines parallel even if the drawing layout changes.
After trying it yourself, choose your next review. This is your self-assessment.
Your review choice appears on Today. Sign in to sync it across devices.
Make it stick
Draw series by one path and parallel by a shared junction pair, then trace every return.
If you needed the solution, close it and solve the problem again from a blank page. A correct answer is stronger when you can explain the reason for each step.